I had the smrdlg problem and resolved that thanks to your help.

However, now when trying to use diskkeeper to defrag I get the msg:
CHKDSK is scheduled to run on the next boot. Until then diskkeeper cannot run.
Help!

Also get the msg AUTOCHECK pgm not found. Is this still related to the smrdlg pblm?

I always defrag in Safe Mode, after deleting all the 1000s of temporary Internet files. There were be just a few files open to interfere with your defragging when in Safe Mode.

Did you allow chkdsk to run at next boot?

Hi and welcome to the WTT forums


If you have scheduled chkdsk to run on the next restart then let it run when you restart your computer.....you may wish to run the f switch or the r switch so the command would be, for example
chkdsk /r
the f switch is then implicit (note the space between the k and the / as it's essential if you are using these switches.
Unfortunately the
smrdlg
that you mention does not mean a lot to us.....are you sure you have correctly identified it?

Similarly with
AUTOCHECK pgm

As this was your first post to us we are not quite sure how we helped you in the past....perhaps you used a different user name?

Post back with more information and we will do our best to help you
Regards
paws

EDIT..sorry Digerati, my slow typing again!

This post has been edited by paws: Mar 2 2008, 12:28 PM

Nothing wrong with teaming up on a problem!

I finally got CHKDSK to run. Still have the AUTOCHECK pgm not found problem but that is minor. A very serious problems is as follows:

My system continually reboots after a system restart or cold boot unless I let it sit for several hours. Some times it may boot into safe mode but not often. Heat problem ?

Any help?

Could be a heat issue - is the system clean of dust and dirt? Do all fans spin freely?

Could also be a failing PSU or motherboard.

Inspect the motherboard for leaking capacitors. Flawed and/or abused (over-heated) capacitors literally bulge at the seams due to excessive internal pressures. Extreme cases result in a firecracker type explosion that really can stink up a room. Typically, they just ooze off the pressure by leaking electrolyte. The electrolyte can be caustic, to motherboards and skin.

These failed or failing capacitors are a common cause of sudden, but seemingly random, system lock ups and reboots. Look for white to dark brown, dried, liquid or foam leaking from the tops or bottoms of the capacitors. The capacitors look like tall soda cans, many of which surround the CPU socket. Bulging capacitors are a sign leakage is about to occur.

A motherboard with bulging or leaky capacitors can be repaired, but often it is more cost effective to replace the motherboard. Inspecting for leaking capacitors is something everyone should inspect for, just as a matter of routine. I normally recommend monthly inspections and cleaning, if necessary, of the computer case interior. This ensures there is no heat trapping dust or dirt buildup on the motherboard, video card, vents, fans, and heat sinks. Give the fans a flick of the finger to make sure they spin freely while in there. Then survey the field for leaking capacitors, loose connections, or anything out of the usual. Be sure to power down, unplug the computer, and keep yourself discharged by touching the bare metal of the case.

Leaky Caps:


Bulging Caps:

thanks for the detailed info on my problem. Will check all u said to check and see if I have any of these problems.
The photos were great.

G'Day ; What is the f switch and the r switch ???


Blessings Miykle

Hi miykle.
Here's a link to the Microsoft page that will give you lots of information on Chkdsk and two of the most frequently used switches.
http://support.microsoft.com/kb/315265
Regards
paws

G'Day there Paws; Thank you kindly for the reply, I had a read but found I had been doing just that for quite a while, I just didn't know it was called switches, I usually do it through My Computer as I have 2 hard drives, one with a partition, so I need to select which one to check.
Thanks again, it all adds to the knowledge base.
Many Blessings Miykle

For a quick reference for chkdsk, you can use the universal switch for command line applications - the /? switch.

Enter: chkdsk /? for a complete list, and brief explanation of the switches, as well as syntax examples.

Thanks Digerati, Yes you are so right, I should have included the reference to the help files in my response to miykle.

Glad you were around to complete the information....

Ah!... my!..... it all takes me back to the "good old DOS" days......sigh..!
Regards
paws